Відео

What kind of plyboard did you use

What is that u’re using for calculations besides Rew?

Škoda toho poškozeného výškového reproduktoru

Your links do not go where there are meant to.

They are beautiful,what finish did you use.Thanks

Hi. How are you going to hang them on a wall without blocking the rear port?

Amplifier link doesn't work

Great video Eric! Enjoying the vids, both relaxing and stimulating! Just liked and subscribed...

How many watts is the subwoofer?

Anh ơi,cho e sơ đồ phân tần được không, cảm ơn a

NO SOUND DEMO ????!

if you where to buy a speaker that can be identical on all channels minus the center channel & Sub's of course , for a 7.2.6 speaker surround setup. choosing (3) different ((( 1st, 2nd , 3rd place ))) pre-build's & (3) D.I.Y from Part Express what would you're recommendations be. can you include 3 chooses from both category's for the budget / value person in mind ...

DIY step one: Build a factory in your garage. 😂

and i say WoW too - exelent work and so "pretty". excuse my bad english

Beautiful speaker. Where did you cross your sub and FR?

awesome build, i just cant get behind that woofer, such low sensitivity, need all 200watts of amp to get good sound out of it. Dayton does offer a few 6" options with sensitivities around the 92db. your getting the same volume for half the amplifier power. if you've got a huge amp, that's fine, but if you want to power it with some little tpa3116d2 chips, you wont get much out of them lol

bravo!

😅😅floorstanding!! With chairfeet. Joking?

0:39 How many viewers cleaned their screen here!

Your job is great, but the speakers principle is terribly wrong . . . .

Ok. So I asked about the 7” version. Maybe with the Dayton audio reference (paper) 7” (x2 maybe) with the 7” epique sub and two 7” PR. Not sure about the amp though. I’d figure with it getting a signal from the receiver that either a passive network or two channel amp would work. I’d def like to hear a demo of this as a pair to see if a sub would even be needed. Even in the 5 1/2” version.

Hey great job where does one find your 🎶 my name is glen

where is the other?

Beautiful. I'd love to see a passive build of these as a stereo pair.

Definitely would’ve used a different method of wiring up the speakers over soldering if something happens to one of the drivers you’d either have to cut the wire or break out the soldering iron, connectors would’ve been a decent option over soldering imo especially for maintenance or driver replacement even modern speakers use spade connectors.

Great video! I didn't understand if you are using two amps with a cable to carry the signal to the other speaker or one amp per speaker.

i would use different drivers but your version is not bad at all. and they look amazing. i would use two dayton audio rs125p-8 for the midrange. the paper based membrane would probably have low dirty resonances in the upper frequency range above 2kHz. i would go for an M-T-M configuration with a Vifa/peerless XT300 KT/4 ring radiator. those tweeters are very smooth because of a low tube-like k3 distortion.

Beautiful but how is the sound ?

😂😂 Lautsprecher müssen klingen. Nicht nur toll aussehen. Wird auch immer schlimmer!! Ist kein Möbelstück 😮😮

Man, I would love to build an audio monitor box, but I can't measure it to make it look good, it's not professional at all, I'd just like to use some speakers I have, there are 3 speakers, one 15w, 5w, and a 2 25w for a 30w tweeter, it would be like a mine tower, could you help me with some measurements or a website so I can build a project?

Listening in mono is just 😘 👌

Very nice , impressed.

How much money does it cost to build this tower?

I found the same type of workbench, a cabinet makers I believe, in an Antique Store some years ago to add to my shop. It didn't have the cabinet below, just a shelf It came with two dog peg of steal o ly more rectangular than these. Along the edges of both wood vises there were saw cut marks and such. I took firstly an electric planner to the entire top, tray, top and faces of the vises to reve gouges and cut markes. It came out beautifully.

Very nice design!!!

Sound demo? It is totally worthless if the sound is not heard...

Is there a crossover that I can buy for this speaker so that I can operate it via an amplifier?

Great Erik. Snyggt. Stylish. Powerful. Umpf. Doff doff. Did you use the acrylic to beam light from a led on the amp board? Duratex better than MDF sealer? Great build.

You are an artist, I'm a fan of you perfect work!!!

looks nice! Just out of curiosity: for the center to center distance, would it not be better to move the active driver to the top opening, or is the XO that low it does not matter much?

Nice job. Realy.

Simply great work! These turned out very well!

Love the design! I was wondering if you did a calculation of the enclosures, I have the impression that the loudspeakers do not work in the optimal parameters due to the dimensions of the speakers. I think it should be bigger. Did you use any app for this? Thank you!

Here we go again! Another banger from my favourite youtuber Erik did it!

Stunning craftsmanship!

👍🏼

Passive Aggressive. It looks like a transmission line box plus passives. Hmm. Bipolar? Regardless it looks really nice.

Holy doly, mate. This looks more like slapping speakers😂 I think best of your projects so far. Cost fortune but I believe that's not what matters this time. Well done again!

Интересное решение и хорошее изготовление! Поздравляю!

No damping material?